Ducati Hyperstrada Forums Ducati Hyperstrada Motorcycle

Go Back   Ducati Hyperstrada Forum > Ducati Hyperstrada Forum > Classifieds

Classifieds Buy, Sell, Trade - Private sales only


Reply
 
LinkBack Thread Tools Display Modes
Old May 26th, 2016, 07:27 PM   #1
Senior Member
 
Joined: Jul 2014
From: California
Posts: 1,192

14mm handlebar spacers

I am selling a pair of 14mm handlebar spacers with new nuts and bolts. This is 5-6mm less than the stock setup.

Decided to try a shorter height and didn't want these to go to waste! Asking $35 shipped in the US. Thank you



kuksul08 is offline   Reply With Quote
 
Old May 27th, 2016, 09:18 PM   #2
Senior Member
 
Joined: Feb 2015
From: Ventura, CA
Posts: 135

I Ride: 2015 Ducati Hyperstrada Monster 796ABS 20th Anniversary, Moto Guzzi V50 III, BMW K100RS, BMW R65
I'm definitely interested! But if I read your post correctly, you went to an even shorter bar height?
BelloStrada is offline   Reply With Quote
Old May 28th, 2016, 09:32 PM   #3
Senior Member
 
Joined: Jul 2014
From: California
Posts: 1,192

Quote:
Originally Posted by BelloStrada View Post
I'm definitely interested! But if I read your post correctly, you went to an even shorter bar height?
Yeah, so I have the SP model which doesn't come with a spacer at all. I wanted to try out something like the Hyperstrada's 20mm spacers, but not as high. So I made these 14mm spacers. Turns out I actually like the stock height or thereabouts (no spacer) or maybe I am just used to that, so I am selling these rather than shaving them down since they're perfectly fine.
kuksul08 is offline   Reply With Quote
Old May 31st, 2016, 08:33 PM   #4
Senior Member
 
Joined: Feb 2015
From: Ventura, CA
Posts: 135

I Ride: 2015 Ducati Hyperstrada Monster 796ABS 20th Anniversary, Moto Guzzi V50 III, BMW K100RS, BMW R65
What's involved as far as the install goes...any crazy access issues requiring disassembly of half the front end?
BelloStrada is offline   Reply With Quote
Old May 31st, 2016, 09:49 PM   #5
Senior Member
 
Joined: Jul 2014
From: California
Posts: 1,192

Quote:
Originally Posted by BelloStrada View Post
What's involved as far as the install goes...any crazy access issues requiring disassembly of half the front end?
Not at all, just removing the 4 screws on the handlebar, then the 2 bolts holding the risers on. I used a ratchet with an extension from the bottom side, and my friend to hold the bolt from the top to hold it from spinning.
kuksul08 is offline   Reply With Quote
Old June 9th, 2016, 12:12 PM   #6
Member
 
Joined: Jul 2013
From: Tujunga
Posts: 59

I Ride: Hyperstrada White
Do the threads protrude pas the nut or is the bolts the exact length?
krolinked is offline   Reply With Quote
Old June 9th, 2016, 01:07 PM   #7
Senior Member
 
Joined: Jul 2014
From: California
Posts: 1,192

Quote:
Originally Posted by krolinked View Post
Do the threads protrude pas the nut or is the bolts the exact length?
They stick past about 3mm to fully engage the nut. No clearance issues whatsoever.
kuksul08 is offline   Reply With Quote
Old June 9th, 2016, 01:15 PM   #8
Member
 
Joined: Apr 2016
From: Canada
Posts: 33

I Ride: 16' HyperStrada, 97' 900ss CR, 78' CB550K
What are the torque specs for the 4 handlebar screws, and the 2 riser nuts? I'm assuming they are the same for the 821 as the 939, but I don't have the 939 service manual yet.

Reason I'm asking is because I'm thinking of removing my 20mm risers.

Thanks in advance
Tron is offline   Reply With Quote
Old June 10th, 2016, 11:52 AM   #9
Member
 
Joined: Apr 2016
From: Green Cove Springs, FL
Posts: 64

The risers screws should be torqued to 45 Nm 5%, following a 1-2-1 sequence.

The top cap/plate screws should be torqued to 25 Nm 5%, following a cross pattern.

Last edited by flvraptor; June 10th, 2016 at 11:54 AM.
flvraptor is offline   Reply With Quote
Old June 10th, 2016, 12:42 PM   #10
Senior Member
 
Joined: Jul 2014
From: California
Posts: 1,192

Quote:
Originally Posted by flvraptor View Post
The risers screws should be torqued to 45 Nm 5%, following a 1-2-1 sequence.

The top cap/plate screws should be torqued to 25 Nm 5%, following a cross pattern.
The top cap is machined such that one side gets tightened first then the other side clamps down. Tighten the side with the arrows first (toward seat), then the other side (dash side).
kuksul08 is offline   Reply With Quote
Reply

  Ducati Hyperstrada Forum > Ducati Hyperstrada Forum > Classifieds

Tags
14mm, handlebar, spacers



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Lower handlebar Yama Hu Mechanical and Technical 13 September 16th, 2016 10:07 PM
Mirror and Handlebar replacement GuyW Mechanical and Technical 12 September 10th, 2016 04:53 PM
Handlebar spacer height kuksul08 Ducati Hyperstrada 7 May 26th, 2016 05:32 PM
Handlebar bolts Rutter Mechanical and Technical 3 April 23rd, 2014 05:45 AM
Handlebar buzz sk57 Mechanical and Technical 0 September 3rd, 2013 07:57 PM


Ducati Hyperstrada Facebook Ducati Hyperstrada Twitter Ducati Hyperstrada RSS Feed



Ducati Hyperstrada Motorcycle Forum
Copyright © 2012-2014 HYPERSTRADA.COM • All rights reserved.