Garage Door Remote Mounting

gatdammit · May 12th, 2013, 09:56 AM

Bought a key chain remote for garage and found a nice place to mount it in grip guard. Just used some industrial velcro and heated up adhesive with blow drier until really gummy. It's very secure, removable and didn't get wet when I rode through storm yesterday. It's tucked in and well hidden though it doesn't look it in picture. I can punch it with a finger without really taking hand fully off bar.

Lawrence of Suburbia · May 14th, 2013, 02:25 AM

[QUOTE=gatdammit;1851]It's tucked in and well hidden though it doesn't look it in picture.QUOTE]

Good move! I had an identical set-up on my BMW R1200 GS - also mounted inside the hand-guard. I went a half-step further and gave it a lick of matte black quick-drying paint (avoiding the little buttons on it) to make it truly invisible to prying eyes.

L of S

Stradasphere · May 14th, 2013, 10:53 AM

I just carry mine in an outside coat pocket and push the button through the fabric.

wildbill · May 14th, 2013, 10:59 AM

Quote:

Originally Posted by Stradasphere

I just carry mine in an outside coat pocket and push the button through the fabric.

I do the same thing, but I do see an advantage of it always being on the bike. I have like 3 different jackets depending on weather and have to remember to move the remote accordingly.

gatdammit · May 14th, 2013, 03:05 PM

Had to be on the bike for me. I wear multiple jackets and put all my pants pocket contents in jacket when I ride, which is an embarrassing amount of trash. I was going to ziptie in a tight location but then saw the little nook in the guards and it was perfect.

gatdammit · May 20th, 2013, 05:40 AM

Found out that isn't ideal location after my remote went skipping down the highway last week...$40 mistake. I should have gone with my gut that the grove on the guard would create a not-so-great contact patch. The vibes finally shook it loose.

I moved location just forward and right of spot pictured. It's the large flat area perpendicular to 1st location, directly in front of clutch lever. It's nice and flat for good contact patch with velcro.

I also attached some small zipties to remote in case it tries to shake loose again. I looped it around hand guard and it's very hard to spot. Only minus there is I'll have to cut the straps to remove it. Thinking about waterproofing remote somehow, as well.

May 12th, 2013, 09:56 AM	#1
gatdammit Senior Member Joined: Mar 2013 From: Naples, IT Posts: 2,251 I Ride: 2013 White Strada	Garage Door Remote Mounting Bought a key chain remote for garage and found a nice place to mount it in grip guard. Just used some industrial velcro and heated up adhesive with blow drier until really gummy. It's very secure, removable and didn't get wet when I rode through storm yesterday. It's tucked in and well hidden though it doesn't look it in picture. I can punch it with a finger without really taking hand fully off bar.

May 20th, 2013, 05:40 AM	#6
gatdammit Senior Member Joined: Mar 2013 From: Naples, IT Posts: 2,251 I Ride: 2013 White Strada	V2... Found out that isn't ideal location after my remote went skipping down the highway last week...$40 mistake. I should have gone with my gut that the grove on the guard would create a not-so-great contact patch. The vibes finally shook it loose. I moved location just forward and right of spot pictured. It's the large flat area perpendicular to 1st location, directly in front of clutch lever. It's nice and flat for good contact patch with velcro. I also attached some small zipties to remote in case it tries to shake loose again. I looped it around hand guard and it's very hard to spot. Only minus there is I'll have to cut the straps to remove it. Thinking about waterproofing remote somehow, as well.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My new Hyperstrada is safely tucked away in my garage	Stradasphere	Ducati Hyperstrada	8	May 4th, 2013 02:23 PM

May 14th, 2013, 02:25 AM	#2
Lawrence of Suburbia Member Joined: Jan 2013 From: Brisbane, eastern Australia Posts: 59 I Ride: BMW R1200R	[QUOTE=gatdammit;1851]It's tucked in and well hidden though it doesn't look it in picture.QUOTE] Good move! I had an identical set-up on my BMW R1200 GS - also mounted inside the hand-guard. I went a half-step further and gave it a lick of matte black quick-drying paint (avoiding the little buttons on it) to make it truly invisible to prying eyes. L of S

May 14th, 2013, 10:53 AM	#3
Stradasphere Senior Member Joined: Dec 2012 From: Central Washington Posts: 294 I Ride: Hyperstrada	I just carry mine in an outside coat pocket and push the button through the fabric.

May 14th, 2013, 03:05 PM	#5
gatdammit Senior Member Joined: Mar 2013 From: Naples, IT Posts: 2,251 I Ride: 2013 White Strada	Had to be on the bike for me. I wear multiple jackets and put all my pants pocket contents in jacket when I ride, which is an embarrassing amount of trash. I was going to ziptie in a tight location but then saw the little nook in the guards and it was perfect.